How To Make French Toast

1. Combine one egg and 1/3 cup milk.

 

2. Add 1 tablespoon of sugar.

 

3. Add some ground cinnamon.

 

4. Mix well.

  5. Dip both sides of the sliced loaf bread to the french toast mixture.

  6. Cook both sides until slightly toasted.

  7. Glaze with cinnamon sugar syrup before serving.

How To Make A Duct Tape Wallet

Everybody needs a wallet, right? If you have a taste for the unconventional, or you're simply a stubborn do-it-yourselfer, then whip out that roll of duct tape and make your own wallet!

What you'll need:
- Duct Tape (duh)
- a ruler/protractor
- a knife (or other cutting utensil, preferably not scissors)
- work space w/ flat surface

Click here to continue reading.

How To Make Bento: Instructional Video

How To Make Fluffy Monster Cellphone Case

Step 1: You Will need
a) Polar fleece
b) Fur fabric
c) Black and white felt
d) Velcro
e) Pins
f) Thread
g) Scissors



Step 2: Cut your fabric out
1) Place your phone onto your fleece fabric, as far away from the edge as the phone is thick, and mark this distance again underneath the phone.
2) Mark this same distance all along the fabric, and cut along the line, making a long strip.
3) Place your phone onto the strip of fabric with enough overhang on one side to wrap all the way over it.
4) Mark this same distance on the opposite side of the phone and cut out. You should now have a rectangle of fabric that can comfortably encapsulate the phone,
with enough for a flap to come back down over the front.
5) Place the fleece onto the reverse side of your fur fabric noting the direction of the fur. Cut out the fur to the same size as the fleece.
6) This is what you should have so far, a piece of fleece and a piece of fur the same size



Step 3: Sew the ends together
7) Now you need to work out what part will be the main case and what part will be the flap. Pin the fabric together, right sides in, at each corner, and fold the fabric
over the phone with about 5mm extra (to account for the seam) marking where it lands.
8) Leaving a 4mm margin on the 'flap' end, sew around the three edges to the marks you made. On the other end just sew straight across the end.
9) Tip: Trim the corners off at 45 degrees, this will give sharper points once you turn it right-way-out.
10) Turn the case the right-way-out, it will look like this.

Step 4: Sew it up and add the velcro
11) Take the edge where you only sewed straight across and fold it to meet where the base of the flap end. Pin in place on both sides.
12) Leaving a 4mm hem sew along this edge with a straight stitch, finish the edges with a zigzag stitch.
13) Cut a piece of velcro about 1cm shorter than the edge of the case, sew the rough side of the velcro onto the lining side of the flap, 5mm away from the edge.
14) Tip: To get the fluffy fibers out of the stitches on the front of the case run an un-picker or knitting needle (don't use anything sharp or you'll tear the fur)
horizontally along the edge.
15) Put the phone into the case and close the flap, mark the case with a pin where it comes down to.
16) Pin the soft piece of velcro onto the case about 5mm above the marker pin you just placed. Sew the velcro in place

Step 5: Making the monster face
17) Take your white felt, place it just underneath the end of the case flap and mark some sharp teeth on it. Cut out being careful to trim away any pen lines.
18) Trim the teeth to fit just underneath the velcro, pin into place. Handsew along the long edge using small neat stitches.
19) Cut two semi circles shapes from black felt and sew on using neat zig zag stitches.

Source: www.instructables.com/id/Fluffy-Monster-Case/